Description

Front Grill [Painted]  – 73,500 yen / [Unpainted] – 62,500 yen
Mid-term model (September 2013 to August 2017) only
・FRP white gel coat finish unpainted product
・Genuine T mark (Toyota mark) emblem can be installed.
・Install the genuine grill-plated frame by transplanting it from the genuine grill.
Also, the genuine T-mark (Toyota mark) emblem will be transplanted in the same way.
・Option A special type for “vehicles with a front camera” is also available.
*It is not possible to install a vehicle equipped with a pre-crash safety system (millimeter wave radar).
The design of the LEXUS GX460 grille, which was well-received in the previous model, has also been adopted in the mid-term model. It has a design that emphasizes a luxurious atmosphere and a wide feeling that is different from the genuine grill.

Front bumper spoiler [Unpainted] – 191,500 yen
Mid-term model (September 2013 to August 2017) only
・FRP white gel coat finish unpainted product
・For fog lamps, genuine products are diverted.
・Includes 5 LED lamps on one side.
Established a big face that is well-balanced with the wider grille area of the mid-term model. The wing-shaped under spoiler placed on the bottom part is well-balanced and has an overwhelming low form and the effect of making the car look bigger.
Resin mesh is used for the mesh net in the center. Contributing to quality improvement.

Rear Bumper Spoiler TYpe 2[Unpainted] – 238,500 yen
For early/mid-term models
* Late model (September 2017-) cannot be installed
・FRP white gel coat finish unpainted product
・2TR-FE (2.7L), 1GR-FE (4.0L)
Compatible with 1GD-FTV (clean diesel).
・Also compatible with 4.0L TZ-G (rear air suspension vehicle)
・Includes LEXUS LS genuine tailpipe diffuser & stainless steel bypass muffler on both sides. It realizes a double-sided exhaust that is not a dummy.
・Includes a reflector.
・Spare tire can be installed.
*It is necessary to remove the tow hook on the rear side.
Duct-style slits on the sides are based on the conventional rear bumper spoiler. And by making the inside of the LS tail a diffuser shape, it has a sporty design.

LED Reflector – 15,500 yen
By replacing and wiring the genuine reflector, 30% of light is emitted when the small lamp is lit, and 100% of light is emitted when the brake lamp is lit, realizing double lighting of small / brake.
Not only does it dress up the rearview, but it also enhances visibility from the following vehicle and prevents rear-end collisions.
* Genuine bumper can be used
* Compatible with genuine KOITO part number: 53-17601L/R

Front Half Spoiler FRP [Unpainted] – 76,500 yen / [Upper part carbon only]  – 105,000 yen
Mid-term model (September 2013 to August 2017) only
・FRP white gel coat finish unpainted product
It is a half-type spoiler that covers the normal bumper.
Produces elegant and sporty styling.

Rear Half Spoiler FRP [Unpainted] – 229,500 yen / [Without Muffler]  – 105,000 yen
・FRP white gel coat finish unpainted product
・For 2TR-FE (2.7L) and 1GR-FE engines
Compatible with 4.0L TZ-G (rear air suspension vehicle)
・Includes a stainless steel rear piece dual tail muffler that realizes realistic exhaust.
・Spare tire can be installed.
・The rear tow hook needs to be removed.
A half-shaped rear spoiler designed for combination with left and right 4 mufflers. Because the shape does not use the genuine rear reflector, it is possible to achieve a large image change from the normal one even though it is a half shape (exclusive reflector included). The dedicated muffler adopts a standard-type tail with a dual 115mm diameter. Equipped with a tail slide function that can be adjusted to your desired width.
*The product has holes for the rear corner sensor and back sensor. If your vehicle is not equipped with it, please purchase a dummy sonar (sold separately).

Sold separately: LED reflector
By replacing and wiring the genuine reflector, 30% of light is emitted when the small lamp is lit, and 100% of light is emitted when the brake lamp is lit, realizing double lighting of the small / brake. Not only does it dress up the rearview, but it also enhances visibility from the following vehicle and prevents rear-end collisions.

Sold separately: Dummy sonar for rear half spoiler
Dummy sonar for vehicles without genuine optional clearance sonar. Attach it to the service hole of the product body with the attached double-sided tape. *The product is not painted.

Rear Half Spoiler Type X [Unpainted] – 259,500 yen / [Without Muffler]  – 105,000 yen
・FRP white gel coat finish unpainted product
・For 2TR-FE (2.7L) and 1GR-FE engines
Compatible with 4.0L TZ-G (rear air suspension vehicle)
・Includes a stainless steel rear piece dual tail muffler that realizes realistic exhaust.
・Spare tire can be installed.
・The rear tow hook needs to be removed.
A half-shaped rear spoiler designed for combination with left and right 4 mufflers. Because the shape does not use the genuine rear reflector, it is possible to achieve a large image change from the normal one even though it is a half shape (exclusive reflector included). The dedicated muffler adopts a standard-type tail with a dual 115mm diameter. Equipped with a tail slide function that can be adjusted to your desired width.
*The product has holes for the rear corner sensor and back sensor. If your vehicle is not equipped with it, please purchase a dummy sonar (sold separately).

Sold separately: LED reflector
By replacing and wiring the genuine reflector, 30% of light is emitted when the small lamp is lit, and 100% of light is emitted when the brake lamp is lit, realizing double lighting of the small / brake. Not only does it dress up the rearview, but it also enhances visibility from the following vehicle and prevents rear-end collisions.

Sold separately: Dummy sonar for rear half spoiler
Dummy sonar for vehicles without genuine optional clearance sonar. Attach it to the service hole of the product body with the attached double-sided tape. *The product is not painted.

Aero step cover – 94,700 yen
Compatible with all year models (for vehicles equipped with standard side steps)
・FRP gel coat finish unpainted product
・With Elford emblem
It is possible to lower the ground clearance by 60mm by installing it over the genuine plate-type side step. Achieves sporty styling by balancing the side view volume when installing external aero parts and genuine OP aero parts. In addition, one of the features is the modeling that supports separate paintings. We also considered the amount of protrusion of the main body so as not to impair the ease of getting on and off.
(Ground clearance) 60mm lower than the original

Side Extension [Unpainted] – 70,700 yen
For cars with genuine option side step cover
・FRP white gel coat finish unpainted product
・Installation uses double-sided tape and screws
An extension part that covers the lower part of the Toyota genuine optional side step cover. The ground clearance is about 45mm lower than the genuine OP side step cover.
Perfect for balancing the side view with the Elford Bumper Spoiler. In addition, it demonstrates a visual lowdown form that does not rely on the use of springs.

Rear Wing [Unpainted] – 62,700 yen / [Painted] – 73,700 yen
・FRP white gel coat finish unpainted product
・Double-sided tape for installation Easy installation
Since it is a rear wing that can be put over the genuine rear spoiler, the genuine high-mounted stop lamp and rear wiper function can be used as they are. From the normal hanging shape, it is slightly larger and extends backward.
The raised lines give it a sportier look.

Leigh weight Aero Bonnet Type 2 FRP [Unpainted] – 149,700 yen / [Upper part carbon] – 195,700 yen
・Early/mid-term models only
・FRP gel coat finish unpainted product
・Weight: 8.5kg (genuine: about 20kg)
*Triple duct and NASA scoop are dummies.
*It requires drilling into the engine room to install the support rod.
The three ducts and NASA scoops* are placed on the left and right to create a sporty look. The product weight is about 8.5kg, which is 50% lighter than the genuine product.
Since it is possible to install a genuine insulator on the back of the bonnet, it does not impair soundproofing and heat dissipation.
In addition, since the genuine bonnet damper cannot be used, a support rod is included.

Leigh weight Aero Bonnet FRP [Unpainted] – 149,700 yen / [Upper part carbon] – 195,700 yen
・Early/mid-term models only
・FRP black gel coat finish unpainted
・Weight: 9kg (genuine: about 20kg)
*It requires drilling into the engine room to install the support rod.
It has a sporty look and is 45% lighter than the genuine product. The back of the duct has a detachable 3-part panel to prevent water such as rain from entering the engine room directly. In addition, since the genuine bonnet damper cannot be used, a support rod is included.

20mm over fender for Elford Aero [Unpainted] – 70,500 yen
Mid-term model (September 2013-August 2017)
・FRP gel coat finish unpainted product
・The rear is divided into 2 parts, consisting of a total of 6 pieces.
*Vehicles with genuine OP side molding require the processing of the product (door part).
20mm wide (one side) over the fender for Elford Aero (front and rear). By increasing the wide feeling, it creates a powerful form and emphasizes individuality as an accent to the side view.
* Structural changes are required due to changes in vehicle width.

20mm over fenders  [Unpainted] – 64,500 yen
Mid-term model (September 2013-August 2017) only
・FRP gel coat finish unpainted product
・Rear divided into 2 parts, 6 pieces in total
*Vehicles with genuine OP side molding require the processing of the product (door part).
20mm wide (one side) overfender for normal bumpers.
Claims individuality with a natural fit like a genuine fender.
* Structural change is required due to vehicle width change.

9mm over fender for Elford Aero [Unpainted] – 64,500 yen
Mid-term model (September 2013 to August 2017) only
・FRP gel coat finish unpainted product
・Rear divided into 2 parts, a total of 6 pieces.
・Compliant with a vehicle inspection.
*Vehicles with genuine OP side molding require the processing of the product (door part).
9mm wide fender for 150 Prado mid-term Elford Aero (front bumper/rear half). The design along the genuine press line realizes a form that does not feel uncomfortable. Accent the side view.

9mm over fenders  [Unpainted] – 58,500 yen
Mid-term model (September 2013-August 2017) only
・FRP gel coat finish unpainted product
・Rear divided into 2 parts, 6 pieces in total
*Vehicles with genuine OP side molding require the processing of the product (door part).
It is a 9mm wide over fender on one side that corresponds to the vehicle inspection, so it casually covers the slight protrusion of the tire. The genuine mudguard is also installed without removing it, and the side view is accented with a natural fit that matches the genuine press line.

protector lamp stay – 105,500 yen
For the mid-term model (September 2013 to September 2017)
・76.3Φ steel pipe powder coating finish
・Stainless steel skid plate included
・ Number relocation plate included
・Body weight: 11.5 kg
・Fog lamps can be installed up to 200Φ.
*When installing a stone guard with a 200Φ lamp, the guard may interfere.
* For standard (normal) bumper
* Vehicles equipped with clearance sonar will interfere with radio waves, so it is necessary to turn off the operation.
*Vehicles equipped with the genuine OP front camera may greatly block the field of view.
It is a lamp stay that enables the installation of a large lamp that is indispensable for off-road driving.
A stainless steel skid plate is standard equipment at the bottom of the product. Gives the Prado a cross-country feel.

Stealth side step – 95,500 yen
for all cars
・50mm×90mm steel pipe powder coating finish
・Anti-slip rubber included
A thin side step that uses an oval shape.
The oval-shaped pipe has a thickness (height) of only 50 mm, so it does not sacrifice the ground clearance and emphasizes the height of the vehicle. However, the step surface (tread surface) has a depth of 90 mm, which is close to a flat shape, making it easy to put your feet on. In addition, if you use the included anti-slip rubber, you can get on and off easily without slipping even in rainy weather. The main body and mounting stay are finished with a semi-matte black powder coating, making it inconspicuous.
Since a strong steel pipe is used for the material, it also plays a role in protecting the side sill when driving on rough roads.
In addition, the main body has a sliding function, so it is possible to adjust the width according to custom, etc. And the products are made in Japan with peace of mind that they are manufactured in Japan.
Despite being a tough existence, it erases its presence. It’s a stealthy sidestep.

Rear under plate – 27,500 yen
・Stainless steel (304 material) hairline finish
・Product weight about 1.8kg
Hides the spare tire visible from under the rear bumper. In addition, the laser-cut “ELFORD” logo beautifully decorates the rear view.
It is also possible to install it together with our company’s “split 4 muffler”.
The installation is a bolt-on installation using genuine screws.

Stealth side step – 60,900 yen / Original 10-inch LED bar light (2 units) included set – 113,000 yen
for all cars
・FRP gel coat finish unpainted product
・Compatible with moonroof vehicles
・Two-piece construction consisting of the main body and the top panel
It is a dedicated panel that mounts a 10-inch LED bar lamp on the roof. Since the bar lamp can be installed without installing a roof rack, etc., the vehicle height does not change, and the center of gravity does not rise, allowing off-road driving while maintaining driving stability. The product consists of two pieces, the main body, and the top panel, and it is easy to adjust the rear axis of the lamp. Installation is fixed with double-sided tape and screws on the genuine molding part installed on the roof, so there is no need to worry about rain leaks.

Lexus type dummy shark fin antenna [Unpainted] – 14,000 yen / [Painted] – 18,000 yen
・FRP white gel coat finish unpainted product
・Paste and fixed with double-sided tape
Paint finish (070) White Pearl Crystal Shine (202) Black

Assist mirror cover [Unpainted] – 10,000 yen
・FRP white gel coat finish unpainted product
・Installation is fixed with double-sided tape

 
Sonic Art Alloy Wheels – 398,200 yen
The concept of Sonic Art is a “Fusion of performance and beauty of appearance”. By adopting a cover type that has little effect on the design and combining it with the concave shape that is dropped from the outermost circumference of the rim to the center part, it has a spoke shape that is supple and stretches from the center to the rim end. In addition to a sophisticated design such as diamond cutting on the spoke surface, the flow-forming method realizes the ultimate lightness (13.4 kg/piece). Although it is 22 inches in size, it is lighter than the genuine wheel, so it also emphasizes athletic performance. Sonic Art is the “lightest and most powerful wheel for Prado”, which is suitable for calling it art that combines performance and aesthetics.
Size: 22 x 9.5J 6H-139.7 Inset +20
Color: Sonic Black / Diamond Cut Face
Flow forming method
Accessories: Aluminum center cover set, Aluminum black air valve
Standard: JWL, VIA standard-compliant product

Bloodstock 1 piece 2 Alloy Wheels – 398,200 yen
Size: 17 x 8.0J 6H-139.7 Inset ±0
Based on one piece of Bloodstock, it is a model specialized for vehicles with over fenders such as Land Cruiser Prado, FJ Cruiser, and Hilux. Round holes, which are the core of the design, are processed in three dimensions, and milling (cutting) is performed on the edges of window openings and irregularly shaped holes. A method to fix the cap is adopted.
Stronger, clearer, one-size-only evolution model. That is Bloodstock 1 piece 2.
Accessories: Center cap set, air valve
Standards: JWL, JWL-T, VIA standard-compliant product

Matt black/Mill dimple
gloss black/polished rim
Silver polish

Bloodstock 1 piece  Alloy Wheels – 288,200 yen
Size: 17 x 8.0J 6H-139.7 Inset +30
The Bradstock design is based on a round-hole dish design that boasts overwhelmingly high strength performance in terms of rigidity and strength. However, the dish design has disadvantages such as a large disk surface area, increased weight, and poor heat dissipation. Therefore, the design of the bloodstock is different from the conventional round hole dish design in order to eliminate the disadvantages. The round hole, which is the core of the design, has been 3-dimensionally processed to create a unique shape that fuses with the dish and spokes. As a result, by widening the hole opening, the weight increase is suppressed and heat dissipation is improved.
Of course, it’s not about performance, but the unique design of Bradstock creates a beautiful form like no other. Milling (cutting) the edge of the window opening gives it brilliance, giving it both daring and high quality. I believe that Bloodstock has been recognized as a classic design that never goes out of fashion by maintaining a consistent design concept from its birth to the present.
A sense of stability and security because it is a classic. That’s the beauty of Bloodstock.
Accessories: Center cap, air valve
Standards: JWL, JWL-T, VIA standard-compliant product

Matt black/Mill dimple
gloss black/polished rim
Silver polish

Bloodstock 1 piece 2 Alloy Wheels – 288,200 yen
Size: 17 x 8.0J 6H-139.7 Inset ±0
Based on one piece of Bloodstock, it is a model specialized for vehicles with over fenders such as Land Cruiser Prado, FJ Cruiser, and Hilux. Round holes, which are the core of the design, are processed in three dimensions, and milling (cutting) is performed on the edges of window openings and irregularly shaped holes. A method to fix the cap is adopted.
Stronger, clearer, one-size-only evolution model. That is Bloodstock 1 piece 2.
Accessories: Center cap set, air valve
Standards: JWL, JWL-T, VIA standard-compliant product

Matt black/Mill dimple
gloss black/polished rim
Silver polish

Hub-centric wheel spacer – 62,800 yen
30mm thick wheel spacer with integrated hub ring developed exclusively for Toyota vehicles. It has a size setting suitable for aero over fenders.
■ Hub diameter: 106.1mm
■ Made in Japan
■ Nut size: M12 x 1.5
■ Outer diameter: 179.0mm
●Accessories: Penetration nuts 12 x 1.5 24 pieces, adapter
For 1 car: 1 set of 4 sheets