Name: JAOS BATTLEZ lift up set VFA ver.B for Hilux 125
Availability: InStock

JAOS BATTLEZ lift up set VFA ver.B for Hilux 125

Product number: A732096B

Please select per-product shipping when placing the order. This can be shipped via economy air shipping to most parts of Asia, the US, and Europe. However, the territories cannot be covered
with this shipping, we may request an additional shipping charge after the buyer places the order.
4.5% deduction when paying via Bank/WISE Payment

Description

A set of front lift-up springs, rear lift-up blocks, and damping force adjustable dampers. Coil springs and lift-up blocks that make use of the characteristic of “soft but stiff” unique to titanium compounds lift up both front and back. Furthermore, the damping force adjustable BATTLEZ damper realizes comfortable driving. Of course, the spring is a Ti-W with a permanent set guarantee. No structural changes are required.

Product content	Front: lift-up spring, damping force adjustable damper Rear: lift-up block kit, damping force adjustable damper, valve grommet
Vehicle height	Lift up Front 35-40mm (2017-2020/08) Front 30-35mm (2020/08-) Rear 30mm

spring

Wire diameter	Front 17Φ
spring rate	Front: 120N/mm
Color	Silver

shock absorber

type	Front: Low-pressure gas twin-tube damper Rear: Low-pressure gas twin-tube damper, Harmoflex mechanism
Damping force adjustment	14 steps dial adjustment type
damping force	Front: Extension side -43~33%, compression side -18~14% (0.3m/sec/genuine ratio) Rear: extension side -9~21%, compression side -50~-35% (0.3m/sec/genuine ratio) )
stroke	Front +16mm, Rear +33mm
body diameter	Front 45φ, Rear 54φ
piston diameter	Front 25φ, Rear 30φ
Color	gray metallic

others

content	Leaf block: Aluminum, cationic electrodeposition coating, BATTLEZ logo stamped long U-bolt: Steel, black coating Propeller shaft angle corrected, block rotation stop type

Mounting information

Mounting method	genuine replacement + bolt-on
installation time	3.0 hours

Precautions/Supplementary Explanation

Attached between the rear leaf spring and the hose. Genuine U-Bolt Replacement
Safety equipment such as driving support systems and collision avoidance systems of each automobile manufacturer may cause erroneous recognition and malfunction of radars, cameras, sensors, etc. due to changes in vehicle height. Please note that we are not responsible for any malfunctions of these systems due to changes in vehicle height due to the installation of our lift-up (or low-down) suspension, or accidents caused by such malfunctions.

If the change in vehicle height is within 40mm, it is treated as a “minor change”, so no procedure is required for structural changes. However, if the total height of the vehicle changes by 40mm or more by installing it together with other products, it may be necessary to carry out a structural change procedure.

Due to the lift-up, there is a possibility that the front side visibility standard (Section 44, Paragraph 5 of the safety standards) may not be met, and it may be necessary to add a forward visibility confirmation mechanism such as a front view camera.
> Front view camera (reference): Our demo car uses the data system MVC811 multi-view camera. Due

to individual differences in the vehicle, it may not meet the standard (height 550mm) for the rush prevention device (rear bumper for Hilux). I have. In that case, it is necessary to readjust the position of the rear bumper or reduce the height of the rear bumper to 550mm or less by using the “JAOS Rear Bumper Down Bracket (B318096).” In some cases, a structural change procedure may be required.

Although the Hilux is equipped with rear fog lamps as standard, the safety standards for rear fog lamps (rear fog lamps) (upper edge of 1 m or less from the ground: Article 37-2 of the safety standards) are stipulated by the lift-up on the rear side. may exceed it. However, since the back fog is not an essential lighting device for safety standards if you physically cancel (remove) it according to the procedure attached to the product, the non-conformance to safety standards will be resolved.

Can be installed after 20.08M/C

packing size
H:525 × W:400 × D:210mm
H:225 × W:230 × D:770mm

Product weight (the weight of the product itself, excluding the package) : 23.35 kg
Packing weight (packing weight) : 26 kg