GARAGE VARY Body Kit for Toyota YARIS
¥165,360
GARAGE VARY Body Kit [FRP] for Toyota GR YARIS includes Front lip spoiler + Side Step + Rear Diffuser
Individual parts also can be purchased. See the prices below.
This can be shipped via economy sea shipping to most parts of Asia, the US, and Europe. However, the territories cannot be covered with this shipping, we may request an additional shipping charge after the buyer place the order. We can combine shipping if you need to purchase multiple items. To do so, please contact us before or after placing the order.
Description
Front Bumper set [GR Yaris look] – 140,000 yen
Please specify if your car is a Toyota stock camera equipped with.
Normally, there is no hole, but if you wish, we can ship it with a hole.
Please specify “Sonar hole, and camera hole” if available on your car.
We have confirmed that the pre-collision safety/radar cruise control/clearance sonar/panoramic view monitor works normally with this bumper, but please note that we cannot guarantee the operation.
No fog lights.
The demo car uses bi-color LED fog lights.
It is also possible to install LED fog lamps.
*Unpainted only.
* Made of white gel FRP with plastic mesh
Front lip spoiler [FRP] – 42,000 yen
Center down amount 30mm Side down amount 15mm Width 30mm (change in total length)
*Unpainted only.
*Made of urethane
*The sticker in the center of this product is not included.
Accessories
・Two 10mm x 1m cut tape adhesives
・5 x 5×16 tapping screws
Side Step [FRP] – 76,500 yen
15mm down from the genuine side
*Only unpainted.
※Made of white gel coat FRP
Accessories
・Cut type tape adhesive 10mm x 1m 4
・5×16 tapping screw 10
Rear Diffuser [FRP] – 40,500 yen
The fin part is lowered by 20mm Protrusion width by 15mm (no change in overall length)
*Please refer to image 4 for aftermarket muffler installation. (The demo car has a normal muffler.)
*Unpainted only.
*Urethane
accessories
・Two 10mm x 1m cut tape adhesive
・Two 5×16 tapping screws
Rear Roof Spoiler [FRP] – 76,500 yen
140mm long from a genuine rear gate
Installation is caulk adhesive + attached cut tape adhesive (caulk should be prepared by customer)
or attached bolt nut + attachment Cut-type tape adhesive (It is necessary to make a hole in the genuine rear gate.) The
washer nozzle part is avoided.
*Unpainted only.
※Made of white gel coat FRP
Accessories
・Cut-type adhesive tape 10mm x 1m x 3
・6×20 truss bolt x 2
・M6 flange nut x 2
Gate Spoiler [FRP] – 48,800 yen
30 mm from the genuine gate (no change in total length)
*Unpainted only.
*Made of urethane
accessories
・ Cut-type tape adhesive 10 mm x 1 m 4 pieces
Over Fenders [FRP] – 50,700 yen
Outer width 9mm
*Vehicles equipped with Advanced Park cannot be installed because this product covers the sensor.
*Unpainted only.
*Made of urethane
accessories
・Cut-type tape adhesive 10 mm x 1 m 1 box
・4 x 5×16 tapping screws
GR YARIS eyelid [FRP] – 26,500 yen
* Only unpainted.
* White gel coat FRP
accessories
-Cut-type tape adhesive 10 mm x 1 m 4 pieces
GR YARIS eyelid [CARBON Twill wave ] – 44,900 yen / [CARBON Plain wave ] – 38,900 yen
* Only unpainted.
* Clear gel coat made of twill weave carbon (buff finish)
Accessories
・ Cut tape adhesive 10 mm x 1 m 4 pieces
GR YARIS bonnet duct rain guard set [FRP] – 44,900 / [CARBON Twill wave ] – 77,900 yen / [CARBON Plain wave ] – 66,900 yen
Cut and attach the genuine bonnet with the attached paper pattern.
* It is recommended to use the bonnet damper as the genuine support rod cannot be used.
Rain guard attached to genuine bonnet Image (Images 4 and 5)
Attached to our original bonnet Image Image 6
* Only unpainted.
* Clear gel coat made of twill weave carbon (buff finish)
* Rain guard made of black gel FRP
Accessories
・ Cut tape adhesive 10 mm x 1 m 3 pieces
・ 4×16 tapping screw (stainless steel) 16 pieces
You must be logged in to post a review.
Reviews
There are no reviews yet.